PDF Bachelor of Science in Biomedical Engineering

EBM 409: Concept Note for the Design of a UV Sterilization Lamp

Concept note for a ultraviolet sterilization lamp: the need for surface and air disinfection in clinical spaces, the germicidal principle, the objectives, resources, and the design approach set for the assignment. Continuous assessment concept note for EBM 409 Machine Design, written on the department's cover with the background, problem, objectives, resources, expected outcome and the design approach.

Document preview

Page 1 of 4 · first page only

PDF

More materials from the same course.

EBM 503: Digital Image Processing Continuous Assessment Test 1 Continuous assessment test one in digital image processing, nine questions. Two commonly used imaging systems with their operation explained; what a digital image processing system is, the operations carried out within it and its diagram; the cross-disciplinary nature of the subject with two of its applications outside medical imaging; the brightness response of the human eye compared with that of photographic film; image formation in mammography, its key applications and the imaging techniques that can complement it; why the low megahertz range is used in ultrasound imaging; the definitions and role in image processing of the grey-level histogram, dynamic range and contrast, entropy, and signal-to-noise ratio; two operations common in image enhancement in the spatial domain; and the filters used to enhance images on social media, with how the equivalent is achieved in the frequency domain. PDF KES 40.00 EEE 408: Engineering Project I Course Outline Second semester unit outline from the Department of Electrical and Electronics Engineering, School of Engineering and Technology: prerequisites, the objective of solving simple engineering problems by integrating course material with practice, the expected outcomes from practical design and research skills to working within approved budgets, the requirement for a project involving specification, review, analysis, design, development and research, and assessment by oral presentation, construction and technical report. PDF KES 40.00 EEE 414: Laboratory Report on Transducers and Signal Conditioners Instrumentation laboratory report: the transducers examined on the bench, their characteristics and calibration, the signal conditioning stages used with them, the readings taken and the results and discussion written up for the unit. PDF KES 40.00 EEE 403: Analogue Electronics III First Semester Examination Analogue electronics paper set for the electrical and electronic engineering and biomedical engineering degrees alike. Works through the operational amplifier: its design and functionality by block diagram, a differential amplifier built from bipolar junction transistors, output voltage from an open-circuit gain of 100 with inputs of 3.25 and 3.15 volts, bandwidth and maximum closed-loop gain from a 15 megahertz gain-bandwidth product, and the maximum operating frequency of an amplifier limited to 0.5 volts per microsecond slew rate at 8 volts peak output. Calculates the output of an inverting stage and of a summing amplifier, and asks for circuits that average three distinct voltages, take the difference of two, integrate a signal and differentiate one. Treats common-mode rejection ratio in decibels, the input impedance and differential gain of a transistor pair, Class B and Class C amplifier designs and the characteristics that make each unusual, input and output impedance and closed-loop gain of an amplifier stage, the instrumentation amplifier, generating a square wave from a sine input, the output of an integrator driven by a square wave, and comparing a signal amplitude against a fixed direct-current reference. Closes on a differential amplifier with a 500 microvolt single-ended signal and 1 volt of 50 hertz interference appearing on both inputs through radiated pick-up, and on bandwidth from a 100 decibel open-loop gain with a 3 megahertz unity-gain bandwidth. PDF KES 40.00 Growing Leaders Programme Session 10: Basic Skills and Techniques of Counselling The practical skills and techniques a leader needs for counselling, on the ground that specific skills must be acquired to support the wholeness and wellbeing of the people being led. Works through the techniques one by one, including reflection of feeling, the attempt to understand a client's point of view and communicate that understanding back so the client can think of their feelings as part of themselves. Ends with the role-play exercise in which each group takes turns as client, counsellor and observer until everyone has played each part, with the facilitator ensuring the practice is done professionally. PDF KES 40.00